Go Back   The Supercar Registry > General Discussion > Pontiac


Reply
 
Thread Tools Display Modes
  #1  
Old 03-26-2021, 02:53 PM
olredalert olredalert is offline
Yenko Contributing Member
 
Join Date: Dec 2002
Location: Marine City, Mi.
Posts: 9,451
Thanks: 33,169
Thanked 4,601 Times in 1,944 Posts
Default

----I'm curious weather big body Pontiacs followed the same path with the vacuum linkage on automatic cars? I remember a member here and friend, Chris P, had a gorgeous resto done on a 64 GTO convert with AC (triple black) and sourced all the vacuum stuff of the internet......Bill S

Last edited by olredalert; 03-26-2021 at 02:56 PM.
Reply With Quote
The Following User Says Thank You to olredalert For This Useful Post:
60sStuff (03-27-2021)
  #2  
Old 03-26-2021, 03:16 PM
Keith Seymore's Avatar
Keith Seymore Keith Seymore is offline
Yenko Contributing Member
 
Join Date: Feb 2009
Location: Motor City
Posts: 2,726
Thanks: 2,738
Thanked 5,124 Times in 1,411 Posts
Default

Man - I don't know about that racing stripe installation at the front...

K
__________________
'63 LeMans Convertible
'63 Grand Prix
'65 GTO - original, unrestored, Dad was original owner, 5000 mile Royal Pontiac factory racer
'74 Chevelle - original owner, 9.56 @ 139 mph best
Reply With Quote
  #3  
Old 03-27-2021, 02:21 AM
60sStuff's Avatar
60sStuff 60sStuff is offline
Yenko Contributing Member
 
Join Date: Jul 2019
Location: Fremont, Ca.
Posts: 1,209
Thanks: 2,203
Thanked 4,854 Times in 924 Posts
Default

Quote:
Originally Posted by olredalert View Post
----I'm curious weather big body Pontiacs followed the same path with the vacuum linkage on automatic cars? I remember a member here and friend, Chris P, had a gorgeous resto done on a 64 GTO convert with AC (triple black) and sourced all the vacuum stuff of the internet......Bill S
Hi Bill,

Yes, the Big cars used pretty much the same Vacuum linkage/components as the A body.

Although the Bigs did not use a throttle cable.
Instead they used link arms and couplings.

Thanks, Chris
Reply With Quote
The Following User Says Thank You to 60sStuff For This Useful Post:
olredalert (03-27-2021)
  #4  
Old 03-27-2021, 03:12 AM
60sStuff's Avatar
60sStuff 60sStuff is offline
Yenko Contributing Member
 
Join Date: Jul 2019
Location: Fremont, Ca.
Posts: 1,209
Thanks: 2,203
Thanked 4,854 Times in 924 Posts
Default

Right Side.

Where would we be without Vacuum.

Brass fittings, steel pipe, crush clamps are what comes off the front carb throttle plate and provides Vacuum for the Power Brake booster, Automatic transmission module and the Vacuum reserve tank.

After this busy intersection comes a check valve leading down to a cast T fitting clamped in place.
One long hose goes to the Vacuum reserve tank mounted up front of the fender skirt.

The other, shorter hose goes to the thermostatic Vacuum control assy.
The purpose of this unit was to disable secondary throttle activation until the engine reached operating temperature (165 degrees).
Attached Images
          
Reply With Quote
The Following 2 Users Say Thank You to 60sStuff For This Useful Post:
grantprix (03-28-2021), RPOLS3 (03-12-2024)
  #5  
Old 03-28-2021, 02:43 AM
60sStuff's Avatar
60sStuff 60sStuff is offline
Yenko Contributing Member
 
Join Date: Jul 2019
Location: Fremont, Ca.
Posts: 1,209
Thanks: 2,203
Thanked 4,854 Times in 924 Posts
Default

Right side secondary arm operation.

End carbs were activated by a Vacuum Control diaphragm.

This “Control” mounted to the two RH rear carb studs and provided the pulling power to open the front and rear Rochester’s.

The two end carbs each had a small throttle return spring that clipped into the base plates to assist with deceleration.

The “Automatic” return springs #7013783 were twice the size of a “Manual Shift” spring #7029689 which (helped) on this Suicide Linkage.

I’ve seen many Original Vacuum Tri-Powers converted over to the Mechanical version and these springs were never changed out, because most are unaware.
Attached Images
       
Reply With Quote
The Following User Says Thank You to 60sStuff For This Useful Post:
olredalert (03-10-2024)
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 09:47 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

O Garage vBulletin Plugins by Drive Thru Online, Inc.