Go Back   The Supercar Registry > General Discussion > Pontiac


Reply
 
Thread Tools Display Modes
  #1  
Old 09-15-2013, 08:46 PM
njsteve's Avatar
njsteve njsteve is offline
Yenko Contributing Member
 
Join Date: Nov 2003
Location: NJUSA
Posts: 8,498
Thanks: 9
Thanked 3,022 Times in 925 Posts
Default Re: The New, Newer Project Part Tres...

And after driving it 75 miles or so in the past week I noticed that the car runs at 205 degrees on the temp gauge. I confirmed this with the infrared heat gun (so the gauge is actually accurate!). The temp would never rise above that, even when sitting in traffic or under throttle - very stable, just hotter than I would like.

Since the thermostat housing was leaking I decided to check the thermostat. Looks like it was the original thermostat with a Delco stamp and a 195 rating.

The unique "LS2" ID stamp on the SD455 intake, and the leaky thermostat housing:



"DELCO" on the top side:



"195" rating on the bottom side:



Since I had a spare 160 thermostat on the workbench, I threw that in, replaced the gasket and tightened everything back up. While I was there I used a little Windex and gently cleaned the area surrounding the housing. With the 160 thermostat in it, the car runs much cooler now - like 160 or so - barely hitting the first notch on the gauge on a 75 degree day today.


Reply With Quote
  #2  
Old 09-15-2013, 09:04 PM
njsteve's Avatar
njsteve njsteve is offline
Yenko Contributing Member
 
Join Date: Nov 2003
Location: NJUSA
Posts: 8,498
Thanks: 9
Thanked 3,022 Times in 925 Posts
Default Re: The New, Newer Project Part Tres...

While under the car yesterday I noticed both valve covers were leaking oil. Not wanting to open the top of the engine I looked closely at the valve cover bolts and noticed that oil was seeping out from under them. When I shut the car off I could see a little bubble of oil oozing out from underneath one of them by the main leak trail. I went to tighten it and it was barely finger tight. So, one at a time I removed each valve cover bolt, wiped it off, applied a bit of sealer on the thread and tightened them down. Hopefully that will stop the leak(s).

As you can see, the wire retainer brackets were on the engines when they were painted:



And the unique SD455 valve cover warning label:



The SD455-only oil filler cap with the PCV within it. The PCV's on the SD455s were relocated to a valve cover oil cap from the intake manifold due to the increased internal pressures in the intake valley where the regular engines have them mounted.



The stenciled hose for the PCV filler cap.

Reply With Quote
  #3  
Old 09-15-2013, 09:10 PM
njsteve's Avatar
njsteve njsteve is offline
Yenko Contributing Member
 
Join Date: Nov 2003
Location: NJUSA
Posts: 8,498
Thanks: 9
Thanked 3,022 Times in 925 Posts
Default Re: The New, Newer Project Part Tres...

Everything back together for a test drive. She sure is a "peppy" little car. Chirps second gear without trying. Definitely pulls all the way up the RPM range. The next thing on the list is to start cleaning everything by hand to get the rest of the four decades of grease and dust off.



Reply With Quote
  #4  
Old 09-15-2013, 09:30 PM
napa68's Avatar
napa68 napa68 is offline
SCR Sponsor
 
Join Date: Oct 2008
Location: Presque Isle, WI
Posts: 3,915
Thanks: 6,053
Thanked 5,549 Times in 1,369 Posts
Default Re: The New, Newer Project Part Tres...

Excellent Steve.......................just excellent!

Tim
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 02:01 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

O Garage vBulletin Plugins by Drive Thru Online, Inc.