Forum: Technical & Restoration
08-21-2024, 01:08 PM
|
Replies: 3
Views: 496
|
Forum: Technical & Restoration
08-20-2024, 07:55 PM
|
Replies: 3
Views: 496
1967 Camaro Upper Door Hinge Rebuild
Well, after 26 years of ownership my upper door hinge has begun to sag on the drivers side. I'd prefer to rebuild the original hinge if possible rather than replacing it with an aftermarket part. ...
|
Forum: Supercar/Musclecar Discussion
08-16-2024, 07:30 PM
|
Replies: 19
Views: 2,666
If you want to hammer on it with no worries of...
If you want to hammer on it with no worries of what happens to the engine, go with more displacement. I have a 406 small block with AFR's, super victor, and a hydraulic flat tappet in my 67 Camaro...
|
Forum: Technical & Restoration
07-09-2024, 07:26 PM
|
Replies: 5
Views: 800
|
Forum: Technical & Restoration
07-09-2024, 06:59 PM
|
Replies: 5
Views: 800
|
Forum: Technical & Restoration
07-08-2024, 10:18 PM
|
Replies: 5
Views: 800
|
Forum: Technical & Restoration
07-08-2024, 12:01 AM
|
Replies: 5
Views: 800
|
Forum: Garages/shops..
06-27-2024, 01:43 PM
|
Replies: 31
Views: 13,771
|
Forum: Garages/shops..
06-26-2024, 08:33 PM
|
Replies: 31
Views: 13,771
Looks good! I put two 84" fans from home depot...
Looks good! I put two 84" fans from home depot on down rods in my 40x60 shop and they move a considerable amount of air and keep it comfortable. However, once outside temps are above 90 degrees, it...
|
Forum: Preservation forum
06-26-2024, 06:47 PM
|
Replies: 266
Views: 130,674
|
Forum: Mopar
06-19-2024, 02:48 PM
|
Replies: 14
Views: 9,103
|
Forum: Mopar
06-19-2024, 02:37 PM
|
Replies: 14
Views: 9,103
Moving on to the engine, it was evident that it...
Moving on to the engine, it was evident that it was filthy, 50+ years of grime, grease and makeshift repairs, it was leaking from every conceivable orifice, but it ran very well, so I decided to put...
|
Forum: Mopar
06-19-2024, 01:46 PM
|
Replies: 14
Views: 9,103
Continuation from the post yesterday. After...
Continuation from the post yesterday. After examining the internals of the trans, everything looked good, so I cleaned it up, replaced the input shaft and output shaft seals and reinstalled the top...
|
Forum: Mopar
06-18-2024, 09:23 PM
|
Replies: 14
Views: 9,103
Well, I've been hard at work on this Truck for...
Well, I've been hard at work on this Truck for the past few months. I'll add posts as I get time to show the progress. I was able to fix all of the oil leaks, replaced the timing set, cleaned the...
|
Forum: Supercar/Musclecar Discussion
05-06-2024, 06:26 PM
|
Replies: 17
Views: 5,534
|
Forum: Mopar
04-26-2024, 01:30 PM
|
Replies: 14
Views: 9,103
No worries Mitch. I've always liked Mopars as...
No worries Mitch. I've always liked Mopars as well. The truck I'm working on now has been a part of my life since I was about a year old. My dad bought it in the mid 80s and used it for his...
|
Forum: Mopar
04-25-2024, 12:46 AM
|
Replies: 14
Views: 9,103
|
Forum: Mopar
04-24-2024, 11:04 PM
|
Replies: 14
Views: 9,103
|
Forum: Day 2 stuff-modified cars
04-24-2024, 08:30 PM
|
Replies: 12
Views: 9,503
|
Forum: Mopar
04-24-2024, 07:56 PM
|
Replies: 14
Views: 9,103
Oil Pan Sealing Tips LA Small Block?
I'm in the process of putting a clutch in my 69 D300 and while the transmission is out, I am fixing the oil leaks coming from the pan. Do you guys have a certain method of installing the gaskets &...
|
Forum: Other Events
03-20-2024, 08:16 PM
|
Replies: 4
Views: 3,442
Bowtie Nationals
Have any of you been to this show before? I've been looking for a good Chevrolet show to attend that isn't too far away from Georgia and this claims to be a great one. I grew up going to Super...
|
Forum: Yenko Chevrolet
02-14-2024, 08:31 PM
|
Replies: 8
Views: 13,082
|
Forum: Technical & Restoration
11-28-2023, 07:55 PM
|
Replies: 5
Views: 2,596
|
Forum: Supercar/Musclecar Discussion
11-27-2023, 03:06 PM
|
Replies: 13
Views: 6,616
|
Forum: Supercar/Musclecar Discussion
11-09-2023, 03:53 PM
|
Replies: 1
Views: 1,080
Was it Johnson county? It looks like there are...
Was it Johnson county? It looks like there are several towns within that county. Wrightsville, Kite, Donovan, Spann and Meeks. I am from North Georgia and am not familiar with the area, but the...
|