1967 ss/rs resto/mod

[Too Many Projects]

This mornings endeavors. I secured the panel while clamped, with drill screws so I can put it right back in the same place after every removal for fitting, prepping, etc.





This is the left corner, that is badly out of place for the dash panel.



I removed the panel and made a pie cut 8" long and 3/8" wide at the outside, tapering it to the inside.



Clamped it tight and drill screwed it in place.



That's the first modification. The entire lip needs to come down for the dash to lay on top, but after tapping the end down, it started to buckle, which I expected. Bending that lip down decreases the radius and the extra metal has to go somewhere. I'll need to make pie cut reliefs every 3-4 inches to get it to cooperate...



Before...




.

[Too Many Projects]

After a little more relocation work on the right corner, I did the cuts in the lip, bent them down and set it back in. The dash is sitting there very lightly touching the channel. I'm very pleased that it fits this well but the real test will be tomorrow when I set the windshield in it. I was going to do that today, but neglected to bring my glass suction cup handles into the heated shop from the back storage room, which is about minus 4 degrees today. They'll be warm in the morning.








..

[Too Many Projects]

Shortly after the last pics, we went to FL for 4 weeks, including the 5 days driving. My wife rode down but flew back, so I took a little detour to Richmond, KY on my way home.



Quite the front room "shop" they have...



I now have a new upper dash panel and dash pad for the car. Over the next few weeks, I hope to have this project done and painted. THEN, I can get started on fitting the NOS fenders I thought I was going to do several weeks ago...



My body guy has been bugging me to get wheel opening trim so we can drill the holes before going any further with paint, so I picked up the GM set that has the step in the rear trims to follow the body line at the lower door and quarter. Also grabbed a few small items to help fill needs down the road. With the crazy shipping costs of oversize items now, I saved about $100, so the few extra miles and gas, as well as getting to see the place and talk with them, was well worth it.

[Too Many Projects]

Removed the top dash panel. I don't like using spot weld drills when I want to save/use the panel below what I am removing. My preferred method is a grinding wheel. I grind around the perimeter of the spot and try to not cut into the substrate at all, or very little.






I use the grinder about the same way I mig weld, using short bursts and checking the color of the metal to "see" where the spot is and work around it until the metal is very thin and I can pop it off with a screw driver.









There were about 16 spot welds and it took about 15 minutes to remove them all. Less time than using a drill and stopping to observe that progress to prevent drilling thru the substrate panel.



This is what I use... That wheel was used when I started and shows almost no wear after all that






After this, I used a 2" disc sander with 120 and cleaned up the spots, removing any of the top panel that was left behind.



It does make a MUCH bigger mess than drilling. I use a shop vac with a HEPA bag filter inside. I can vacuum filler dust and dried overspray and it never comes out the exhaust.









It does fit and line up nicely, but It would be even better if the pre-punched holes for the trim clips and glass stops lined up with the holes in the cowl panel. It may well be the cowl that is off, as 3 of the 4 holes for the cowl grill aren't accurate either. Just a little more work later to drill the holes in the correct places.

[dykstra]

Looking great Mitch! Probably a relief to have that unexpected bump in the road finished.

[Too Many Projects]

There was a lot more to this project. I still had to weld the replacement cowl piece in and the dash top on.





Steering column/instrument panel brace. It had 15 spot welds on it, but only THREE were holding. None of the rest penetrated. It's not going to fall off now..





All done and working on sanding the entire instrument panel for paint.

[scuncio]

Nice work.

[69M22Z]

Wow!! Nice!!

[Too Many Projects]

That was a couple weeks ago and I since removed the rear axle and springs assembly to clean and prep the new trunk floor for paint. THAT was a bear, laying on a creeper and getting as wet as the car. I still need to do finish grinding of welds in tight areas and sand them.
Soooo, I gave in and did what I said for 15 years I wasn't going to do with this car...

Went out in the back shed and dug out the rotisserie...




I bought this from a guy who built it to restore a '69 Firebird. It came with these adapters for the rear spring mounts, so I thought this would be a quick knockdown from the arms I built for the '67 GTO and my '66 Chevelle.




I spent 3 HOURS trying to figure out how he had those rear arms on the lifts, because no mater how I arranged the drilled holes he made they would NOT line up...
I finally gave in and just drilled new holes for them to fit the car and moved on.



I have 6' rectangle tubes to fit on the forks for this stuff.

[Too Many Projects]

This was an interesting discovery, especially since I've had this driveshaft out for 3 engine/trans changes over the years. I never noticed this before...





.