Passing the time during COVID-19 pics

[67since67]

I enjoy running equipment almost as much as being in the shop.
I replaced the 185 with an X320 which was a smooth running refined mower.
When I built the new place in 2015 I scored major points with Jani by bringing home a this 1025R. She won't let me near it for mowing, and the Yanmar diesel uses less than half the fuel. I put more than 40 hours on it that first year doing all manor of loader and three point work.

[MosportGreen66]

Originally Posted by 67since67

I enjoy running equipment almost as much as being in the shop.
I replaced the 185 with an X320 which was a smooth running refined mower.
When I built the new place in 2015 I scored major points with Jani by bringing home a this 1025R. She won't let me near it for mowing, and the Yanmar diesel uses less than half the fuel. I put more than 40 hours on it that first year doing all manor of loader and three point work.

That tractor is lucky to be in your care Bill...

[njsteve]

Is that a photo when it was new? or do you wash and wax that tractor in your off hours? :-)

[njsteve]

You made with all jealous with that JD 1025R photo so last night I pulled the busted headlight pod out and fixed it.

It's a terrible design with the fragile plastic lens sticking out beyond the hood and just begging things to smash it. It's been long since discontinued from JD and you rarely see one used and in one piece on ebay. (That's where I got the spare one several years ago).

So I found my old spare busted original pod in the garage, cut a section of heavy clear plexiglass out of the sheet that I bought years ago to get a 6" square for CC'ing cylinder heads. I then used epoxy and clamped it together overnight. This morning I sanded the edges to match the outer perimeter and reinstalled it. Now I can happily night mow again.

[ss427copo]

Steve, you sound like me with my 24 yr old Craftsman. On my second deck. Fixed this, fixed that, then just ordered a new one last fall. Replaced the smoking engine with a used one 5 years ago. It took a shit! Went to PowerEquipmentDirect and bought a Briggs & Stratton Professional Series™ 540cc 19 Gross HP OHV. Just replaced the transaxle too. Duct tape here, epoxy there and even added a 12v headlight, horn and LED tail light.

I’m going to have it at my funeral service!
Jersey Jeff

[300deluxe]

Planned-Demic

[njsteve]

Originally Posted by ss427copo

Steve, you sound like me with my 24 yr old Craftsman. On my second deck. Fixed this, fixed that, then just ordered a new one last fall. Replaced the smoking engine with a used one 5 years ago. It took a shit! Went to PowerEquipmentDirect and bought a Briggs & Stratton Professional Series™ 540cc 19 Gross HP OHV. Just replaced the transaxle too. Duct tape here, epoxy there and even added a 12v headlight, horn and LED tail light.

I’m going to have it at my funeral service!
Jersey Jeff

You got a horn and tail lights? Are you making beer runs when the wife is away????

(I'm jealous now)

[Verne_Frantz]

Steve,
Funny that I would run across this article. About 6 years ago I bought this 216 from the mid '80s. Single cylinder, old tech but I love the "variactor" Variable speed drive in any gear. This is right after I bought it before any cleaning or maintenance. Since then, new tires and rear wheels, several belts and fluid changes. It does the job very nicely.
I'm told by the tractor-pull guys that the Kohler 16hp is the favorite engine for that hobby.
Verne

[njsteve]

Nice old tractor Verne!

Yesterday I decided to be nice and ordered some new rear tires for the old 185. Only I have come to learn that this series of tractors is cursed with a tendency to weld their rear rims to the axles after 31 years or so of use. I removed the snap ring, fully expecting the wheels to slide right off like the manual says...yeah right. This is the reason they went to bolt on wheels on the more recent tractors.

And of course there is no ledge or collar to attach a gear puller too. Most people try a torch on the back side of the wheel hub but that rarely works and damages the transaxle seals. Other method is drilling two holes in the rim face and using a harmonic balance puller with the bolts through those holes. That rarely works, too. And if you hammer too much on the rim face or axle you can pop the internal snap ring off inside the case, requiring the entire transaxle to be rebuilt. Another method is to weld a short collar onto the rim hub and then try to use a gear puller. Not very effective either. It seems the consensus from owners is disassembling the transaxle, pulling the axles, and then using a hydraulic press to press to axles out.

So my only choice is to see if my lawnmower guy can dismount and mount the new tires while they are still on the tractor.

Here's a photo of me doing my biblical Samson imitation while my wife Delilah laughs in the background. No, this didn't work either, and the Temple of John Deere is still on four wheels.