![]() Dedicated to the Promotion and Preservation of American Muscle Cars, Dealer built Supercars and COPO cars. |
|
Register | Album Gallery | Thread Gallery | FAQ | Members List | Calendar | Become a Paid Member | Search | Today's Posts | Mark Forums Read |
![]() |
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
![]()
Both of the heater hoses are ribbed and the ribs are on the bottom side of the hoses. They are also crossing over each other. In the past I have tried to keep them nice and neat.
|
#2
|
|||
|
|||
![]()
wire seperators
|
#3
|
|||
|
|||
![]()
Does anyone know how long between when the engine is painted that the spark plugs go in ? Are the engines test fired on the assembly line ? I have a bunch of pics of the plugs and most have what looks like orange engine paint. Like specs. Not overspray but I am trying to imagine a painted engine being test fired before maybe puddled paint is completely dry ? I dunno but it is curious.
![]() |
#4
|
|||
|
|||
![]()
.
|
#5
|
|||
|
|||
![]()
.
|
#6
|
|||
|
|||
![]()
.
|
#7
|
|||
|
|||
![]()
.
|
#8
|
|||
|
|||
![]()
[ QUOTE ]
. [/ QUOTE ] Great pix Charley. This is one helluva lot better than anything on TV. And I'll send you a Mickey Mouse band aid for that battle scar. (Actually, I'll see if I have one with Goofy on it.) ![]()
__________________
Don't mistake education for intelligence. I worked with educated people. I socialize with intelligent people. |
#9
|
|||
|
|||
![]()
------Charlie,,,I was going to try to paraphrase what I have heard John H say about prep done to these engines prior to painting in relation to the spark-plugs, but I dont think I would say it right. Ill alert him to this thread and see if he can shed some light.......Bill S
|
#10
|
|||
|
|||
![]()
[ QUOTE ]
Does anyone know how long between when the engine is painted that the spark plugs go in ? Are the engines test fired on the assembly line ? I have a bunch of pics of the plugs and most have what looks like orange engine paint. Like specs. Not overspray but I am trying to imagine a painted engine being test fired before maybe puddled paint is completely dry ? I dunno but it is curious. ![]() [/ QUOTE ] Engines were hot-tested (using an adapter and natural gas for fuel and a slave ignition harness with a coil and plug wires that was part of the test stand) at the engine plant; it only ran for 30-40 seconds, just long enough to set the timing and check for leaks/noises. From hot-test it went to the paint booth (at 300 per hour), which was preceded by a masking operation, where they placed cardboard tubes over the spark plugs, put a piece of tape on the front pad, put a cardboard tube over the water pump shaft and hub, taped-off the fuel pump opening, masked the carb pad surface, put a coffee can over the distributor, and placed vacuum-formed plastic covers on aluminum intakes and aluminum valve covers. The guys on each side in the paint booth had twelve seconds to spray it, and there was a de-masking area after the exit from the spray booth to remove the plastic covers, cardboard tubes, tape, etc. From there the engine was routed to the correct spot on the shipping dock for the designated assembly plant, racked (3 to a rack), and loaded in rail cars; the paint air-dried on the way to the dock. Photo below taken in 1955 shows engines at the shipping dock being pulled off the conveyor and placed in racks - the engine state of dress as shown didn't change appreciably until the early 80's - Chevy V-8's were pretty "naked" when they left Flint V-8 (and Tonawanda). ![]() ![]()
__________________
'69 Z/28 Fathom Green CRG |
![]() |
Thread Tools | |
Display Modes | |
|
|