Go Back   The Supercar Registry > Classified Section > Parts/Memorabilia - Wanted

Please note


Reply
 
Thread Tools Display Modes
  #1  
Old 07-28-2004, 02:52 AM
70LS6454 70LS6454 is offline
Yenko Contributing Member
 
Join Date: May 2003
Location: Maryland
Posts: 292
Thanks: 34
Thanked 33 Times in 27 Posts
Default WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

I would like to find a set of original valve covers with good to exc chrome.The drivers side should have the two clips for the TCS wires and the pass side should have one clip for temp sending unit.

Thanks
Ray
Reply With Quote
Click here to view all the pictures posted in this thread...
  #2  
Old 07-30-2004, 03:32 PM
Unreal Unreal is offline
Senior Member
 
Join Date: May 2000
Location: Chattanooga, TN, USA
Posts: 1,335
Thanks: 1
Thanked 77 Times in 48 Posts
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

I may have what you need, in OK to good condition. (I personally would rechrome) Anyway, what should the firewall side end of the driver side one look like...I have several, including the raised bump, the silver dollar flat, or the flattened corner.
Reply With Quote
  #3  
Old 07-31-2004, 02:14 AM
70LS6454 70LS6454 is offline
Yenko Contributing Member
 
Join Date: May 2003
Location: Maryland
Posts: 292
Thanks: 34
Thanked 33 Times in 27 Posts
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

Correction the pass side should have the 2 TCS clips and the driver side has the one clip for temp. sender.

Ureal,not sure how to describe it to you.It will have an slight slant toward one corner.Do you have any pictures of the ones you have?

thanks
Ray
Reply With Quote
  #4  
Old 08-02-2004, 01:49 PM
Unreal Unreal is offline
Senior Member
 
Join Date: May 2000
Location: Chattanooga, TN, USA
Posts: 1,335
Thanks: 1
Thanked 77 Times in 48 Posts
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

I have the following:
Pass- 2 sparkwire towers, 2 inside clips, 1 outside clip
Pass- no towers, no clips
Pass- 2 towers, no clips

Driver- 2 towers (chevelle position) 1 outside clip, slanted rear with bumpout on top inside.

Driver- 2 towers (chevelle position,) no clips, slanted rear with bumpout on top inside.

All need minor dolly work, and rechromed, all have drippers.


Driver- 2 towers (chevelle position, but unattached) no clips, slanted rear with bumpout on top inside.

Driver- 2 towers (camaro position) outside clip, slanted rear with small flat at 60* on bottom outside.

Driver- 2 towers (chevelle position, but unattached) 2 inside clips, straight rear with silver dollar flat on top outside.
Reply With Quote
  #5  
Old 08-03-2004, 05:00 AM
70LS6454 70LS6454 is offline
Yenko Contributing Member
 
Join Date: May 2003
Location: Maryland
Posts: 292
Thanks: 34
Thanked 33 Times in 27 Posts
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

Unreal,I have a lead on a pair.I will let you know if it falls through.

thanks
Ray
Reply With Quote
  #6  
Old 08-04-2004, 12:01 AM
CamarosRus CamarosRus is offline
Senior Member
 
Join Date: Apr 2000
Location: Auburn,WA (between Sea&Tac)
Posts: 2,697
Thanks: 126
Thanked 273 Times in 98 Posts
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

Curious if anybody reading this thread has knowledge of replacing broken off wiring securing "clip".....and is there any way to restore the FLASH chrome....versus full on SHOW chrome.....Chuck S Seattle
__________________
Chuck Sharin
[email protected]
Auburn,WA (30 miles South of Seattle)
70 Camaro R/S Z-28, L-78, R/S SS
69 Camaro COPO "recreation"
Reply With Quote
  #7  
Old 08-04-2004, 01:04 AM
68SSCamaro 68SSCamaro is offline
Senior Member
 
Join Date: May 2003
Location: Southern California
Posts: 299
Thanks: 0
Thanked 1 Time in 1 Post
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

I'm also interested in an answer to this question. I have a one that has a short spark plug tower missing and one that has a crack in it from a dent. Both covers will need to be rechromed.
__________________
Martin Foltz
68 Camaro SS-396
L35/M20, Corvette Bronze, black vinyl top
George Olsen Chevrolet San Francisco
Reply With Quote
  #8  
Old 08-04-2004, 11:08 PM
68z302 68z302 is offline
Senior Member
 
Join Date: Sep 2002
Location: Vancouver, BC
Posts: 310
Thanks: 0
Thanked 0 Times in 0 Posts
Default Re: WANTED ORIG 70 CHEVELLE BIG BLOCK VALVE COVERS

I thought this was covered.
https://www.yenko.net/ubbthreads/show...rev=#Post20969
Is there any updates since?
__________________
Rob
'68Z, original drive train

AS1 AO1 D55 J52 U17 U69 Z28
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:45 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.

O Garage vBulletin Plugins by Drive Thru Online, Inc.