My 67 chevelle convertible project
 

Well as most of you know I was trying to sell my chevelle project that I have been working on for about a year. I gave it some thought and I am pretty sure I am going to finish the car, just put it on hold for a couple of months. I am building a new garage and it would just drive me crazy knowing I can't work on both threw out the summer. But I am going to just have to deal with it.

I installed the body back onto the frame today the car is going to be real nice when it is done? I have one question for anyone with a 67 chevelle. Do I have the rear wiring harness in correctly? Does this clip on the wiring harness under the dash look correct!

Thanks Jason

http://i35.photobucket.com/albums/d1...ale/0008-9.jpg

http://i35.photobucket.com/albums/d1...ale/0005-6.jpg

http://i35.photobucket.com/albums/d1...ale/0006-5.jpg

Re: My 67 chevelle convertible project
 

Yes thats correct, last time i Had the carpet out of my 67, it went through the same spot.

Re: My 67 chevelle convertible project
 

Thanks for the reply. If you look close at the top bracket you can see the clip I am refering too on the wiring harness!

Re: My 67 chevelle convertible project
 

Well it has been a long year and a lot of hard work! I couldn’t be any happier with the panel alignment. I just have to test fit my bumpers. Then it comes back apart to epoxy all the panels. It sure does make you feel good when you get to this point in your restoration. You can almost see the light at the end of the tunnel!

http://i35.photobucket.com/albums/d1...ale/0002-5.jpg

http://i35.photobucket.com/albums/d1...ale/0003-4.jpg

http://i35.photobucket.com/albums/d1...ale/0004-7.jpg

http://i35.photobucket.com/albums/d1...ale/0005-7.jpg

http://i35.photobucket.com/albums/d1...ale/0006-6.jpg

http://i35.photobucket.com/albums/d1...ale/0009-5.jpg

http://i35.photobucket.com/albums/d1...le/0008-10.jpg

Re: My 67 chevelle convertible project
 

Just wanted to update everyone on my 67 chevelle project. Just painted some panels today check it out over at team chevelle. It has come a long way!

Jason

http://www.chevelles.com/forums/show...64#post2530664

Re: My 67 chevelle convertible project
 

Looks great! https://www.yenko.net/ubbthreads/imag...iggthumpup.gif That's going to be sharp when it's done.

Re: My 67 chevelle convertible project
 

Looks great Jason! https://www.yenko.net/ubbthreads/imag...s/headbang.gif

Re: My 67 chevelle convertible project
 

Looking sweet! Keep up the good work.


Jason

Re: My 67 chevelle convertible project
 

Well guys the car is 99.9% finished. I found my breaker for the convertible top won't hold a load. That is the only thing left to do. I am going to put it on the road this week and wait for the nice weather for the first voyage. Wish me luck! https://www.yenko.net/ubbthreads/imag...ins/3gears.gif https://www.yenko.net/ubbthreads/imag...ins/3gears.gif https://www.yenko.net/ubbthreads/imag...s/headbang.gif https://www.yenko.net/ubbthreads/imag...s/headbang.gif

Ps: as soon as I get the car out and put some miles on it just to make sure the car has no issues, look for it in the fore sale section of the forum! If interested shoot me a PM!

Jason

http://i35.photobucket.com/albums/d1...5Image0001.jpg

http://i35.photobucket.com/albums/d1...5Image0002.jpg

http://i35.photobucket.com/albums/d1...5Image0003.jpg

http://i35.photobucket.com/albums/d1...5Image0005.jpg

Re: My 67 chevelle convertible project
 

Jason does all the work himself https://www.yenko.net/ubbthreads/imag...iggthumpup.gif very talented young man. I'm sure it looks nicer in person...how about some under the hood and interior pics..??

Nice Job...wilma https://www.yenko.net/ubbthreads/imag...lins/beers.gif