Motion phase III Vette emblem? (help needed)
 

I know that there is a huge amount of knowledge on this forum and I have been trying for days to locate this emblem that belongs on the rear of my '69 Motion Vette.

So far I got lucky and found a brand new "SS427" Impalla emblem locally. When I held it up to the back of my car, the holes that had been filled in with bondo lined up perfectly. Now I need to find some of the original Ford GT? emblems that Joel used under the SS427 Impalla emblem. So far, all of them that I can find, are thiner in the stroke of the letter than the ones that are shown in the article in Car's Magazine (Aug 69). This is the last piece of proof that I need to verifiy this was the same car that is on the cover of the afore mentioned magazine.

http://www.motionperformance.com/magazine/69motvet.html

If anybody has access to 67 Mustang GT emblems or a pic of them from back then please let me know. I have been told that these are what Joel used and yet all of the reproductions I can find are not the same. I have been told that they are a first design or early 67 GT emblem and then they made a skinny GT emblem which is all that I can find now. Thank God that I don't need two pair of them. Of course I would take them if I can find some.

(I am posting a pic of the original GT emblems that came on my '70 Motion Phase III car but they are different from what is on the back of the '69 SS427 that was Joel's first Phase III car). These are the correct emblems for the '70, as they are still on the car today.

Thanks in advance, to all that take the time to read this. I realize that I am asking for a Ford part on a GM forum but they are a part of the past too and it is ok if we admire more than one car maker's products. In fact I used to run a used Car lot called Super Cars here in Tulsa OK. I loved all of them. I had so much fun back then. All of the cars of the late 60's through the early '80's were fun.
Please post if you have any knowledge you can share on this subject.

Re: Motion phase III Vette emblem? (help needed)
 

Larry, I'll see what I can find out to help and I'll keep an eye out on ebay as well. [img]/ubbthreads/images/graemlins/biggthumpup.gif[/img]

Re: Motion phase III Vette emblem (FOUND??)
 

I think after a week of searching the net for somekind of 1 st design mustang emblem I think that I have found a emblem that more looks like the one in the magazine articles. It looks like a 65-69 Pontiac GTO grill emblem. I think that Joel must have cut the "O" off and then cut the small bar at the bottom of the letters that linked them together so that they were one complete emblem instead ot 3 seperate one's. If anyone has a different thought about this or want to suggest something else, please let me know? Just as soon as I can locate one for sale I will be able to cut it up and see if it lines up with the holes that have been filled in on the back of my car. Here is a pic of the back panel above the tag where the emblem was removed and filled in with bondo??

Re: Motion phase III Vette emblem (FOUND??)
 

Pantera,
Cosidering I dont know much about Corvette frames maybe I can help with the GT Ford emblem. I am currently restoring a 68 Team Shelby Trans Am Mustang, #2, I have accumulated a lot of Ford and mustang parts in the process. I have several different designs of the GT emblems, I will take some pix tommorow and Email them to you.
Motown [img]/ubbthreads/images/graemlins/beers.gif[/img]

Re: Motion phase III Vette emblem (FOUND??)
 

Here is one showing the holes that have been filled. The white looking one in the center at the top all alone is where the burgler alarm from the factory was filled in.

Re: Motion phase III Vette emblem (FOUND??)
 

one more without the ruller

Re: Motion phase III Vette emblem (FOUND??)
 

I would agree with you Larry.

Here's a comparison: The Motion Corvette rear you speak of vs. a '67 GTO grille...

There is a definite slight flare outward in the "T" width, from its intersection toward its base visible on both emblems.

Re: Motion phase III Vette emblem (FOUND??)
 

Looks to be the exact same scrip design, if it wasnt the one it sure could be. I would think they would have used a GM emblem over Ford, I will check with Jim Mattison as he is the owner of Pontiac Historical Services and may know if the GT emblem is Pontiac. He also ran the COPO department at Chevrolet and was good friends with Don Yenko, he may know what Motion was up too, or discovered the info since with the Historic Pontiac research. I will give it a shot tommorow.
Motown [img]/ubbthreads/images/graemlins/beers.gif[/img]

Re: Motion phase III Vette emblem (FOUND??)
 

Thanks guys I am glad to hear that.

If anybody has a broken GTO grill emblem in their junk box I would like to buy it just to see if it will corespond to the bolt holes that are filled in on the back of my car. From what I can see it must be only one bolt per letter? At the top R of each letter. Of course there were no pins to locate it at the bottom since it had a thin metal strip that holds the three letters together. I asked Joel about it but no reply so far. I think I will pose it to Gary the Painter as he must have had them off to paint the Black stripe on the car for Joel.
I would be suprised if anybody else bothered to research this back then as it was "THE" only one made by Joel this way. In 70 they came out with the 454 and when He made this first 69 car, nobody knew that they would have the bigger motor in 70.On the 70 GT cars he used a 67 Mustang GT emblem (see pic of my documented 70 Phase III) No doubt about what this one is off of.

That was the my problem. I spent two weeks looking at Mustang GT emblems on the internet and here in Town. Finally some one said they thought it looked more like a Vega GT emblem (but they were not built in 69) so that started me to look at any of the other car makers that had the GT models and that was a dead end. Then by accident I found a site that had every emblem for cars back then by maker and I went through every 65 to 69 car till I noticed the GTO grill emblem just by accident and realized why he used it.

It is the only one that comes close to matching the SS on the 427 impalla emblem above it. also it is the right height to boot. all he had to do was cut the brace off at the bottom of each letter and use the GT and it looked good. they probably came loose everytime you washed the car though with only one bolt holding them on. (I guess I will find out but nowadays I have some good glue to hold it still.)

Re: Motion phase III Vette emblem (FOUND??)
 

Evidently Motion used more than one style of GT emblem, because the Corvette Azrapse posted is definitely different than the ones on your car. Thats not to say someone didn't replace one or the other with the wrong emblems somewhere along the line, but it would not surprise me if Motion used whatever he could get his hands on, and varied the actual emblems used. Pantera, the ones on your car in the pic you just posted are DEFINITELY Ford pieces. If not Mustang, try Torino GT. I actually think thats what they are... post these pics on a ford forum and you'll get an identification answer as fast as if you posted a 68 Impala SS427 emblem on here. [img]/ubbthreads/images/graemlins/biggthumpup.gif[/img]