shifter hole
 

where does the hole go in the floor for a four speed on a 69? is there a cutout for the shifter? thanks jerry

Re: shifter hole
 

In a 69 Toyota Corolla it goes just ahead of the seat belt holes.

Re: shifter hole
 

If it is a Chevelle https://www.yenko.net/ubbthreads/imag...mlins/wink.gif there are two different pieces that get welded over the floor cutout hole depending on whether you have a console or non console car. Tomorrow I can probably get enough dimensions to get you in the ball park for location.

Re: shifter hole
 

[ QUOTE ]
In a 69 Toyota Corolla it goes just ahead of the seat belt holes.

[/ QUOTE ]
Thats no way to treat a Newbie. What 69 car do you need the hole for??? Mark

Re: shifter hole
 

yes it mite be a honda

Re: shifter hole
 

What part number hole are you looking for? https://www.yenko.net/ubbthreads/imag...mlins/hmmm.gif

Re: shifter hole
 

[ QUOTE ]
where does the hole go in the floor for a four speed on a 69? is there a cutout for the shifter? thanks jerry

[/ QUOTE ]

if it's a VW or Corvair just push out the cardboard on the dotted lines.

welcome https://www.yenko.net/ubbthreads/imag...iggthumpup.gif https://www.yenko.net/ubbthreads/imag...mlins/flag.gif

Re: shifter hole
 

Fill out your profile so that I can send you some pictures and dimensions.

Re: shifter hole
 

[ QUOTE ]
In a 69 Toyota Corolla it goes just ahead of the seat belt holes.

[/ QUOTE ]

That isn't where it is on MY Corolla. I think you are full of it. Charley, you must be thinking of the Cressida.

Oh, wait, you mean the 69 Corolla with the 396 in it (which you undoubtedly gleaned from his name which is MY69396) right?

Re: shifter hole
 

sorry for the confussion. it is a camaro that i am putting a four speed in.

Re: shifter hole
 

in that case a torch will do the trick

Re: shifter hole
 

Don't pay attention to these smart asses. Yes, the originals were indeed cut with a torch. You obviously want to know WHERE to cut out. I believe that if the tunnel is original, you will find four little dimples representing where the four screws go to hold down the shift boot trim piece. Drill those out, screw the trim piece in place, and you can use it as a template to mark the hole.

Hope that helps. If not, let me know. I believe I have some template instructions at the office.

Lynn

Re: shifter hole
 

Here are some photos to help you cut your hole. https://www.yenko.net/ubbthreads/imag...iggthumpup.gif
http://i7.photobucket.com/albums/y29...ifterhole1.jpg
http://i7.photobucket.com/albums/y29...ifterhole2.jpg

Re: shifter hole
 

That hole is for a 1967 car and probably a automatic not correct for a 69 4speed.

Re: shifter hole
 

Ok I found one you should be able to use. This is from a original 1969 SS 4speed car from california and is a LOS car. http://fototime.com/4F6A22BFA43E4D4/standard.jpg

Re: shifter hole
 

Another http://fototime.com/A36B27061E5912E/standard.jpg

Re: shifter hole
 

Ok how about these two pictures...
http://i7.photobucket.com/albums/y29..._parts_028.jpg
http://i7.photobucket.com/albums/y29..._parts_031.jpg

Re: shifter hole
 

if i recall right a auto hole only needs to be trimmed on the left up to 1/4" from the screw hole on the left and the shifter factory or a hurst console shifter clears properly and the factory dust boot lands back down on the factory screw holes. if you look at the two pics you will see the 1.5" diff, no need to go crazy cutting, 10 mins with the jig saw does the job

B.

Re: shifter hole
 

poster not looking for auto hole,....4spd=torch

Re: shifter hole
 

This photo from a original Z28
http://i246.photobucket.com/albums/g...DSC06843ET.jpg