WANTED: Corvette 1966 427ci engine or parts
 

WANTED: 427ci block, casting # 3869942 (must be `65 or`66 cast date) or casting # 3904351, or possibly 3855961. Must be excellent condition, no liners or repairs. Stock bore prefered.

Also wanted: Heads, cast # 3873858 (or possibly, any `65 or `66 Hi-Po heads considered. Must be cast date `65 or `66. Would also consider complete engines, I will collect and ship, What have You?
Thanks. [img]/ubbthreads/images/graemlins/beers.gif[/img]
Forgot to mention: contact me on [email protected]
or phone: 011-44-1252-343401 (GMT London, England)

Re: WANTED: Corvette 1966 427ci engine or parts
 

Peter,

------If this engine is destined to nestle into a 66 Corvette you should not consider a 351 block.942s actually slipped into early 1967 Vettes,not the other way around!Hope this helps,and I will keep an eye out for you..........Bill S

Re: WANTED: Corvette 1966 427ci engine or parts
 

Hi Bill,

Many thanks for your reply. Just to clarify, do you mean the 351 # is Okay, and the 942s could, or did slip into `67? Everything I need is not going into a 100% restoration of a `66 Vette, it's for a race car. We are building an Appendix `K` FIA circuit race car, to compete in classic road racing events around Europe.To comply with the strict regulations all the engine components must be date coded to the build date of the car. In this case the car was built Mid Sept `65, but we want to run a 427ci so I assume the cast date needs to be early `65? Is this correct. Confusing I know!

Again, thanks for your reply,

Peter.

Re: WANTED: Corvette 1966 427ci engine or parts
 

Peter,

-----If the rules are fast and hard the only block you can use in this instance is a 942.962 blocks were used exclusively in 65 and were 396 blocks.I would have to double check in Noland Adams book but I dont think any 962 blocks came in 66 Corvettes.In any event a 962 block would be way more difficult to find anyway.
-----Just looked in the book and Noland is saying that some very early 66s had a block with 961 as the last three casting digits.I personally have never seen a 961 block so would think a search for one of them would be fruitless.
-----I also called one the block suppliers in the local area and he is just too high priced to even give you his phone number.Stupid money!He must have overpaid!Hope this helps..........Bill S

Re: WANTED: Corvette 1966 427ci engine or parts
 

Pete,

I don't know if you've tried either of these guys (one of them might be who Bill was talking about):

Tracy Performance

Cranes Corvette

You could also try Al Fierke at Chicago Corvette Supply(708) 458-2500.

Re: WANTED: Corvette 1966 427ci engine or parts
 

Bill the 961 block is a 2 bolt 66 block a dime a dozen. [img]/ubbthreads/images/graemlins/haha.gif[/img]

Re: WANTED: Corvette 1966 427ci engine or parts
 

-----Be pretty careful with Cranes.David is OK but there have been times when his representation of parts has been questioned.
-----Dont think Al at Chicago Corvette will be able to help you,but you never know.Ask for Bob Sindelar when you call there as he will be the most helpful.
-----As far as the 961s go,I didnt know that.I should have stated that I have never seen a 961 in a 1966 Corvette,and I have looked at,literally,hundreds.And over the years I never really looked at any low horsepower passenger cars casting numbers.
-----Possibly,Peter could get a cheap 961 block for his purposes(racing)and just massage the 1 into a 2,and make it into a 4 bolt main.That way a good 962 block that might be needed for a correct high-point restoration wouldnt get used up and Peter wouldnt use up alot of money on a bare block he just as easily could spend putting more horsepower into it.I doubt the number checkers in Europe would check as carefully as NCRS or B.G.Hope this helps..........Bill S


-----By the way,almost forgot about the heads.Any of the above mentioned would be good choices for your search for heads as well!!!!!!!!

Re: WANTED: Corvette 1966 427ci engine or parts
 

Bill the 961 I have never seen in a Vette. I didn't read your post right. I thought you were saying you never seen a 961 block period. Sorry for the misunderstanding I can't believe Adams would say that, because this block is a 396 block not a 427 block apparently any thing is possible. Kim

Re: WANTED: Corvette 1966 427ci engine or parts
 

If you don't find a complete motor,I have a couple sets of '66 858's.Both sets are complete and ready to go.Just make a fair offer.$800-$1000?
Jim [img]/ubbthreads/images/graemlins/flag.gif[/img]

Re: WANTED: Corvette 1966 427ci engine or parts
 

Watch out for Chicago Corvettes. I know a disaster story that evolved from the garage of that shop.

-Dan

Re: WANTED: Corvette 1966 427ci engine or parts
 

Since you guys are in the Corvette circles, I have a never stamped 63 Block I will sell. Still has the Factory Broach marks.

Re: WANTED: Corvette 1966 427ci engine or parts
 

Mosport,

------I completely understand your helping comments in regard to Chicago Corvette,but if Peter has occasion to call them and use the name that I gave he will be fine.Bob is one of the most ethical guys I have ever known and is a credit to any business.He absolutely would never steer anyone wrong.I dont give out names of people to deal with lightly.
------This is not to imply that anyone else at CC is anything other than ethical,just that I only know Bob and Al the owner and cant speak for any other employees.........Bill S

Re: WANTED: Corvette 1966 427ci engine or parts
 

I should not have jumped the gun there. I am sorry. I only know of one story and of course, because my buddy obviously told me a one sided story. I made an incorrect statement. I have never ordered anything from CC, but I am sure they are good guys. It would not make sense if a business of this nature could stay alive without being a good ethical business. Peter, let us know how if we helped. We are all in this is learn more. Talk soon. Again, I am sorry.

-Dan

Re: WANTED: Corvette 1966 427ci engine or parts
 

Dan

----An apology was probably not really necessary,however much appreciated!With all the weird Pontiac posting going on around here I think manners and civility are an important thing,and you have shown them both.Thanks!........Bill S

Re: WANTED: Corvette 1966 427ci engine or parts
 

No worries. I just treat other people like I would like to be treated. Plain and Simple. Peter let us know how the Corvette is coming along.

Re: WANTED: Corvette 1966 427ci engine or parts
 

Peter,

-------858 alert!!!!!!!Got my NCRS driveline today and theres a set for sale.No price.Also intake(5069)again no price.-------Phone no.847-433-6610...That puts the stuff in the Chicago area.I happen to be going to Vettefest this Sat.Wonder if the stuff will be there?...........Bill S

Re: WANTED: Corvette 1966 427ci engine or parts
 

Not sure if you found what you wanted but heres a 66 427 from the Team Camaro site. Not out of a Vette though but still might work for you???

http://www.camaros.net/cgi-bin/cyber...hoto_size=full