Re: Camaro getting painted ...
 

[ QUOTE ]
Is that part of the exhaust going on the car, peeking through the floor pan?

[/ QUOTE ]
<font color="blue">
You got it right. I designed an exhaust in my head, (because the car has verry little ground clearence), &amp;
with the welding skills (&amp; same crazy mind) of Gene Goodyear it came to life.

https://www.yenko.net/attachments/376...8Medium%29.JPG

https://www.yenko.net/attachments/376...8Medium%29.JPG

The exhaust slips together, so no clamps hanging &amp; even has a bolt in crossover pipe.
This saved me 1.5" which was what I needed.

I Silver Ceramic Coated the headers (for obvious reasons) &amp; black ceramic coated the exhaust &amp; crossover. It looks killer.
</font>

Re: Camaro getting painted ...
 

What a Car https://www.yenko.net/ubbthreads/imag...ins/3gears.gif

Re: Camaro getting painted ...
 

<font color="blue">A little more work before going to the Darrell Gwynn Show tonight.

http://i67.photobucket.com/albums/h2...n/DSCN0001.jpg

http://i67.photobucket.com/albums/h2...n/DSCN0005.jpg

http://i67.photobucket.com/albums/h2...n/DSCN0004.jpg

http://i67.photobucket.com/albums/h2...n/DSCN0003.jpg

http://i67.photobucket.com/albums/h2...n/DSCN0011.jpg

I will finish that tomorrow &amp; then seal it all up &amp; install the rear. </font>

Re: Camaro getting painted ...
 

<font color="blue">Caulking really stinks ...
but this became my best friend ...

http://i67.photobucket.com/albums/h2...N0164Large.jpg

It is only slightly bigger than a std. gun &amp; much easier to use..

http://i67.photobucket.com/albums/h2...N0165Large.jpg

http://i67.photobucket.com/albums/h2...N0166Large.jpg

... as you can see it isn't bad. Polyurethane is tough to work with (I found out)but it's getting there.


finally finished the back &amp; got the 9" in there.

http://i67.photobucket.com/albums/h2...N0172Large.jpg

http://i67.photobucket.com/albums/h2...N0174Large.jpg

http://i67.photobucket.com/albums/h2...N0173Large.jpg


more to follow https://www.yenko.net/ubbthreads/imag...mlins/hmmm.gif... shortly.

https://www.yenko.net/ubbthreads/imag...lins/beers.gif </font>

Re: Camaro getting painted ...
 

<font color="blue">Got my new M/T SR's today ....

http://i67.photobucket.com/albums/h2...DSCN0004-2.jpg

Threw the trunk lid on for effect. Blue tape prevents https://www.yenko.net/ubbthreads/imag...emlins/eek.gif
Tires are not mounted yet, but I had to see what they looked like.
I am feeling better the closer it gets to the ground. </font>


https://www.yenko.net/ubbthreads/imag...lins/beers.gif

Re: Camaro getting painted ...
 

Most impressive. Thanks for the update. https://www.yenko.net/ubbthreads/imag...iggthumpup.gif

Re: Camaro getting painted ...
 

Mike,Has "NASA" given you a launch date yet---------Looks well thought out..

Re: Camaro getting painted ...
 

THANKS FOR SHARING.

Re: Camaro getting painted ...
 

[ QUOTE ]
Mike,Has "NASA" given you a launch date yet---------Looks well thought out..

[/ QUOTE ]

<font color="blue">"The little motor that could" is on the dyno &amp; giving me a headache.
Tuner says, "cam is too big, headers are too big, blower is too big ... or motor is too small."

http://i67.photobucket.com/albums/h2...s/DSCN0140.jpg

Here is the start-up minute of video.

http://i67.photobucket.com/albums/h2...DSCN0027-2.jpg

It's popping around 5K.
I tested the valve springs (since they have been there a while)
&amp; they are on the weak side (120 instead of 170)
Changing them this weekend &amp; try again.</font>

Re: Camaro getting there ...
 

<font color="blue">Finally getting on the ball with the car.

Got the trunk internals all sorted out &amp; installed.

http://i67.photobucket.com/albums/h2...DSCN0164-1.jpg

Not much room for beer https://www.yenko.net/ubbthreads/imag...mlins/hmmm.gif
... maybe next to the battery https://www.yenko.net/ubbthreads/imag...lins/beers.gif

http://i67.photobucket.com/albums/h2...DSCN0172-1.jpg






more to come, soon https://www.yenko.net/ubbthreads/imag...ns/burnout.gif</font>