Re: Any interest in a "correct" deck lid Posi Decal?
 

I'll take two when they are ready to go.

Re: Any interest in a "correct" deck lid Posi Decal?
 

Don,
I've seen a number of variations in the weight of the fonts along the bottom. Verne Frantz's original label and Sam Griffith's original show the differences quite obvious. I even checked out a couple more at the Gibb Show this weekend.
Again I say, these things were furnished to GM over a number of years and likely came from a number of different vendors (or maybe printed in the individual assembly plants ???) so who's gonna be the "expert" to stand up and say "They should ALL be EXACTLY alike!!!" https://www.yenko.net/ubbthreads/images/graemlins/no.gif

I'd give your version a 99% approval rating! GO FOR IT! https://www.yenko.net/ubbthreads/imag...iggthumpup.gif

Re: Any interest in a "correct" deck lid Posi Decal?
 

[ QUOTE ]

so who's gonna be the "expert" to stand up and say "They should ALL be EXACTLY alike!!!" https://www.yenko.net/ubbthreads/images/graemlins/no.gif

https://www.yenko.net/ubbthreads/imag...lins/beers.gif Very well stated Mr Cumby https://www.yenko.net/ubbthreads/imag...mlins/grin.gif
That profound statment my apply to some other "stuff" too. https://www.yenko.net/ubbthreads/imag...lins/dunno.gif

Re: Any interest in a "correct" deck lid Posi Decal?
 

Don,
ill take 5. can I pay with beer cans?

Re: Any interest in a "correct" deck lid Posi Decal?
 

Mike, I think it does apply to "other stuff" !!! https://www.yenko.net/ubbthreads/imag...ns/naughty.gif
Grady https://www.yenko.net/ubbthreads/imag...ins/3gears.gif

Re: Any interest in a "correct" deck lid Posi Decal?
 

[ QUOTE ]
Don,
ill take 5. can I pay with beer cans?

[/ QUOTE ]
Ah, ah - so that was you I was cursing at 7:00 AM at our Club's Chevelle Show https://www.yenko.net/ubbthreads/imag...emlins/mad.gif https://www.yenko.net/ubbthreads/imag...emlins/mad.gif https://www.yenko.net/ubbthreads/imag...lins/beers.gif

Normally nobody stayed up later than me at the nightly Bench Racing Session, but I guess I wasn't out in the parking lot late enough for this one. Was that payback for me embarrassing you on stage during the awards ceremony a few years earlier https://www.yenko.net/ubbthreads/imag...s/confused.gif https://www.yenko.net/ubbthreads/imag...mlins/wink.gif

Actually, I don't think you were there the year they did it to the car Donnie, maybe you are referring to the truck in an earlier year https://www.yenko.net/ubbthreads/imag...lins/dunno.gif https://www.yenko.net/ubbthreads/imag...lins/smile.gif

http://www.pbase.com/don_lightfoot/image/115702561.jpg

http://www.pbase.com/don_lightfoot/image/115703345.jpg

Re: Any interest in a "correct" deck lid Posi Decal?
 

Too funny Don! https://www.yenko.net/ubbthreads/imag...mlins/grin.gif

People seem to have a thing with you car? https://www.yenko.net/ubbthreads/imag...ns/worship.gif

Re: Any interest in a "correct" deck lid Posi Decal?
 

[ QUOTE ]
People seem to have a thing with you car? https://www.yenko.net/ubbthreads/imag...ns/worship.gif

[/ QUOTE ]
Ain't that the truth Bruce https://www.yenko.net/ubbthreads/imag...lins/dunno.gif

DENNIS - thanks for your above comments and ongoing input https://www.yenko.net/ubbthreads/imag...iggthumpup.gif

Re: Any interest in a "correct" deck lid Posi Decal?
 

Don,
Looks good,but the only thing i found wrong was the letter (A) in caution.The center on the (A) needs to be a little smaller if possible.

Re: Any interest in a "correct" deck lid Posi Decal?
 

True Mark. The "A" was one of the letters I had issues with. I was going back and forth with different fonts. I forgot to put the "A" in CAUTION back to the appropriate font before I printed that draft and took that picture. I noticed it after I posted the picture on here.