The Supercar Registry - What caused this?

The Supercar Registry (https://www.yenko.net/forum/index.php)

- Pit Area - Racing (https://www.yenko.net/forum/forumdisplay.php?f=97)

- - What caused this? (https://www.yenko.net/forum/showthread.php?t=89868)

Re: What caused this?

[ QUOTE ]
Best Answers - Chosen By Voters

...the new one will NOT slip right on...you have to put it on to the best of your ability...and then start hitting it with a soft hammer around the edges until it goes down a little bit. then, put the main bolt in, tighten to where it's tight, and then pound some more. the bolt's tension will help pull the balancer on, because pounding alone will take forever and hurt your arm. But, don't try to skip the pounding and just use the bolt, because there aren't enough threads on that bolt to pull the balancer in by itself until it's in some more.

Source(s):

The Mother Ship.

[/ QUOTE ]

[ QUOTE ]

Put a small dab of silicone in the key way of the balancer (oil can leak past key way) start the balancer then use a big dead-blow hammer or sledge hammer with an aluminum block(wood block)
Then pound away near the center. Install bolt/washer and torque it.

Source(s):

http://painintheexhaust.blogspot.com...

[/ QUOTE ]

<font color="blue">Thanks to ... </font>

http://sg.yimg.com/i/sg/answers/sg_logo_ga.gif
<font color="red"> (&) How to you install a harmonic balancer in a 5.0 ford engine??</font>

Re: What caused this?

yahoo singapore....hmmmmm
I'll have to write that down https://www.yenko.net/ubbthreads/imag...mlins/haha.gif

Re: What caused this?

Please, don't use a hammer to pound a harmonic damper in place. https://www.yenko.net/ubbthreads/imag...emlins/eek.gif https://www.yenko.net/ubbthreads/images/graemlins/no.gif

I've seen a damper split right down the snout while being pounded in place with a 5 lb mallet and a 2X4 block of wood.

If you plan on doing engine work with any frequency at all, a balancer puller/installation tool is well worth the investment.

http://www.sallee-chevrolet.com/Prof...s/66514pro.jpg

Before someone thinks about installing a damper with a hammer & a block of wood, they should take into consideration how much damage a fragged damper could do if it decided to let go at 7K+ rpm.

Eric

Re: What caused this?

Not to mention the potential damage they are doing to the thrust washer. https://www.yenko.net/ubbthreads/imag...s/rolleyes.gif
Rick

Re: What caused this?

"Brute strength,ignorance and vise-grips"......Companion tools of the hammer...otherwise known as.."BFH"

Steve

Re: What caused this?

and of course a sawzall for easy removal of misinstalled parts! https://www.yenko.net/ubbthreads/imag...mlins/haha.gif

Re: What caused this?

FOR THOSE OF YOU WHO THINK YOU HAVE TO USE A TOOL TO INSTALL A STOCK TYPE HARMONIC BALANCER, HA HA HA. WE BROKE (1) AFTERMARKET CHEAP PIONEER BRAND BALANCER BECAUSE OF A BURR ON THE CRANKSHAFT SNOUT IN YHE LAST 15 YEARS. GIVE ME A BREAK, YOU GUYS PROBABLY RUN AWAY FROM A PRESS WHEN ITS GOING TO POP OFF A BEARING OR SOMETHING. STOP READING THOSE MAGAZINES AND PICK UP A WRENCH. USE THE TOOL IF YOU LIKE OR HAVE A FLUID DAMPER, ETC.. BUT DON'T SIT THERE AND SAY THE BALANCER IS GOING TO BREAK IF YOU POUND IT ON. GO TO YOUR LOCAL ENGINE REBUILDER AND SEE HOW MANY TIMES THEY USE THE TOOL BESIDES TEARDOWN TO REMOVE IT.

Re: What caused this?

[ QUOTE ]
FOR THOSE OF YOU WHO THINK YOU HAVE TO USE A TOOL TO INSTALL A STOCK TYPE HARMONIC BALANCER, HA HA HA. WE BROKE (1) AFTERMARKET CHEAP PIONEER BRAND BALANCER BECAUSE OF A BURR ON THE CRANKSHAFT SNOUT IN YHE LAST 15 YEARS. GIVE ME A BREAK, YOU GUYS PROBABLY RUN AWAY FROM A PRESS WHEN ITS GOING TO POP OFF A BEARING OR SOMETHING. STOP READING THOSE MAGAZINES AND PICK UP A WRENCH. USE THE TOOL IF YOU LIKE OR HAVE A FLUID DAMPER, ETC.. BUT DON'T SIT THERE AND SAY THE BALANCER IS GOING TO BREAK IF YOU POUND IT ON. GO TO YOUR LOCAL ENGINE REBUILDER AND SEE HOW MANY TIMES THEY USE THE TOOL BESIDES TEARDOWN TO REMOVE IT.

[/ QUOTE ]

See my first post... https://www.yenko.net/ubbthreads/imag...mlins/haha.gif

Steve https://www.yenko.net/ubbthreads/imag...lins/beers.gif