Re: 143 Blueprint Cam Install
 

Sounding good Ken, my 396 /375 hp 68 nova will be, up and running soon.Can"t wait to hear that sound.we all can thanks rob Clary and Jim Lerum in the chevy camp for this camshaft.Chris Teed

Re: 143 Blueprint Cam Install
 

I have the 143 Crane made cam and it doesn't run worth a darn with the manifolds and the correct dual exhaust .But it sounds good .I need to try headers and a twin muffler set up and see what happens .

Re: 143 Blueprint Cam Install
 

[ QUOTE ]
I have the 143 Crane made cam and it doesn't run worth a darn with the manifolds and the correct dual exhaust .But it sounds good .I need to try headers and a twin muffler set up and see what happens .

[/ QUOTE ]
I don't wanna sound like a *douche*, but I'll say there's a good chance it ain't the manifolds/exhaust that's hurting the performance...even if it's the original 2.5" exhaust [actually <2" in spots] it'll still let a BBC do it's thing.

Re: 143 Blueprint Cam Install
 

[ QUOTE ]
I have the 143 Crane made cam and it doesn't run worth a darn with the manifolds and the correct dual exhaust .But it sounds good .I need to try headers and a twin muffler set up and see what happens .

[/ QUOTE ]

We have seen this camshaft work very well at the drag strip with decent exhaust. I agree with Rob, it's not the camshaft that is holding you up. If it is then you are very light on the compression. 396/375 motors have made 450 on the dyno with that camshaft.

More camshafts and lifters on the way to those who have ordered. Rob will PM you if its coming to your door.

Jim

Re: 143 Blueprint Cam Install
 

I still think its the exhaust .The car has great torque until the revs increase then it just holds back .Its at the paint shop now,when I get it back I will do some more looking .

Re: 143 Blueprint Cam Install
 

[ QUOTE ]
I still think its the exhaust .The car has great torque until the revs increase then it just holds back .Its at the paint shop now,when I get it back I will do some more looking .

[/ QUOTE ]
Just as a point of reference, our Y-Camaro put down ~370hp to the wheels through the original manifolds & chambered exhaust, on a 10:1 *bone stock* L72 build...went mid-high 12s @ 108 at a 3700-3800 race weight on Polyglass, running pump gas. With a little more compression, the car now runs high-11s @ 117+, through the same original exhaust manifolds , and a Pypes 2.5" transverese muffler...both engines would easily rev to 7k+. Terry Pennington's Camaro runs high 10s @ 130+ through the exact same exhaust manifolds in the F.A.S.T. class...

One problem I've seen before exhaust-wise is, the flapper in the passenger side down pipe get stuck shut & cause some problems. Any idea where your timing/jetting are?

Re: 143 Blueprint Cam Install
 

Valve springs
Larry

Re: 143 Blueprint Cam Install
 

Valve springs are originals but were checked .Timing is at 36 total,jetting is 70 primary and stock secondarys on a 4557 carb.The engine has 15,000 miles not rebuilt .My next move will be to set it at TDC and check the mark on the balancer to see if it has moved .I get no spark knock with pump premium and 11:1 comp .

Re: 143 Blueprint Cam Install
 

If you plan on running this car, get rid of those stock valve springs. They either (A) broke and dropped a valve, or (B) couldn't keep up with the cam allowing the valve to free fall shut at high rpm. This eventually pounded the keepers through the retainer allowing a dropped valve again. These are the main reasons that there aren't too many original L78s and L72 out there. We didn't seem to have any problem with the L88 springs in the old days.

Re: 143 Blueprint Cam Install
 

That was true to a point.
For 1970 model production,Chevrolet used a more dureable BB valve spring that avoided dropped valves @ higher RPM.
During 1968-9,they started to see an increase in BB warranty claims filed do to unreliable valve springs,so they used the stronger #3970627 to replace the weaker #3859911 spring.
L-88's were exclusive to the #3916164 spring.